Articles
Update cisco 300-135 tshoot braindump
by Gregor Yedell Actual Exam Questions And Answers This allow you to have more ample time to prepare for the exam. So that you can eliminate your psychological tension of exam, and reach a satisfactory way.In order to meet the needs of each candidate, the team of IT experts in Passtcert are using their experience and knowledge to improve the quality of exam training materials constantly. We can guarantee that you can pass the CCNP 300-135 exam the first time. If you buy the goods of Passtcert, then you always be able to get newer and more accurate test information. The coverage of the cisco 300-135 tshoot braindump of Passtcert is very broad.
In such society where all people take the time so precious, choosing Passtcert to help you pass the Cisco certification 300-135 exam is cost-effective. If you choose Passtcert, we promise that we will try our best to help you pass the exam and also provide you with one year free update service. Passtcert cisco 300-135 tshoot braindump provide the two most popular download formats. One is PDF, and other is software, it is easy to download.
Share some CCNP 300-135 exam questions and answers below.
The fault condition is related to which technology?
A. NTP
B. IP DHCP Server
C. IPv4 OSPF Routing
D. IPv4 EIGRP Routing
E. IPv4 Route Redistribution
F. IPv6 RIP Routing
G. IPv6 OSPF Routing
H. IPV4 and IPV6 Interoperability
I. IPv4 layer 3 security
Answer: G
The Fault Condition is related to which technology?
A. BGP
B. NAT
C. IP NAT
D. IPv4 OSPF Routing
E. IPv4 OSPF Redistribution
F. IPv6 OSPF Routing
G. IPv4 layer 3 security
Answer: G
Ticket 5 R1ACL
TROUBLE TICKET STATEMENT:
The implementation group has been using thetest bed to do a ¡®proof-of-concept¡¯that required both client 1 and client 2 to access the Web Server at 209.65.200.241.After several changed to interface status, network addressing, routing schemes and layer 2 connectivity, at trouble ticket has been opened indicating that client 1 cannot ping the 209.65.200.241 (internet Server).
show run by yourself to obtain the following information:
Client 1 is not able to reach the WebServer at 209.65.200.241. Initial troubleshooting shows that R1 is also not able to reach the WebServer. R1 also does not have any active BGP neighbor.
Configuration on R1
! interface Serial0/0/0/1
description link to ISP
ip address 209.65.200.224 255.255.255.252
ip access-group edge_security in
ip nat outside
ip virtual-reassembly
ntp brasdcast client
net broadcast key 1
no cdp enable
!! ip access-list nat_traffic permit 10.1.0.0 0.0.255.255
ip access-list nat_traffic permit 10.2.0.0 0.0.255.255
! ip access-list edge_security deny ip 10.0.0.0 0.255.255.255 any
ip access-list edge_security deny ip 172.16.0.0 0.15.255.255 any
ip access-list edge_security deny ip 192.168.0.0 0.0.255.255 any
ip access-list edge_security deny ip 127.0.0.0 0.255.255.255 any
ip access-list edge_security permit ip host 209.65.200.241 any
On which device is the fault condition located?
A. R1
B. R2
C. R3
D. R4
E. DSW1
F. DSW2
G. ASW1
Answer: A
What is the solution to the fault condition?
A. Under the interface Tunnel34 configuration delete the tunnel mode ipv6 command.
B. Under the interface Serial0/0/0.34 configuration enter the ipv6 address 2026::34:1/122 command.
C. Under the interface Tunnel34 configuration enter the ip address unnumbered Serial0/0/0.34 command.
D. Under the interface Tunnel34 configuration delete the tunnel source Serial0/0/0.34 command and enter the tunnel source 2026::34:1/122 command.
Answer: A
Ticket 4 NATACL
TROUBLE TICKET STATEMENT:
The implementation group has been using thetest bed to do a ¡®proof-of-concept¡¯that required both client 1 and client 2 to access the Web Server at 209.65.200.241.After several changed to interface status, network addressing, routing schemes and layer 2 connectivity, at trouble ticket has been opened indicating that client 1 cannot ping the 209.65.200.241 (internet Server).
show run by yourself to obtain the following information:
Configuration on R1
ip nat inside source list nat_pool interface Serial0/0/0/1 overload !
ip access-list standard nat_pool
permit 10.1.0.0
! interface Serial0/0/0/1
ip address 209.65.200.224 255.255.255.252
ip nat outside
! interfaceSerial0/0/0/0.12
ip address 10.1.1.1 255.255.255.252
ip nat inside
ip ospf message-digest-key 1 md5 TSHOOT
ip ospd authentication message-digest
On Which device is the fault condition located?
A. R1
B. R2
C. R3
D. R4
E. DSW1
F. DSW2
G. ASW1
Answer: A
The Fault Condition is related to which technology?
A. BGP
B. NAT
C. IP NAT
D. IPv4 OSPF Routing
E. IPv4 OSPF Redistribution
F. IPv6 OSPF Routing
G. IPv4 layer 3 security
Answer: C
R1 and R2 OSPF neighbor.
Which two statements are true? (Choose two)
(Output from show ip ospf neighbors on 2 routers, one of them shows FULL/DR, the other FULL/-, you need to know how were they configured and will they exchange routes)
A. They are not neighbors
B. R1 (non-DR) will not update its routes to R2
C. Router R2 is configured with ospf point-to-point command (R2 is the router that shows as FULL/-)
D. They need to be configured as OSPF NBMA
E. R2 should be configured as stub
Answer: BC
What is the solution of the fault condition?
A. Under the BGP process,enter the bgp redistribute-internal command
B. Under the BGP process, bgp confederation identifier 65001 command
C. Delete the current BGP process and reenter all of the commands using 65002 as the AS number.
D. Under the BGP process, delete the neighbor 209.56.200.226 remote-as 65002 command enter the neighbor 209.65.200.226 remote-as 65002 command.
Answer: D
Which command will limit debug output ppp authentication on serial 0/1 and serial 0/2?
A. debug condition interface range s0/1 -0/2
debug ppp authentication
B. debug condition interface s0/1 & 0/2
debug ppp authentication
C. debug int s0/1
debug int 0/2
debug ppp authentication
D. Debug condition interface s0/1
Debug condition interface s0/2
debug ppp authentication
Answer: D
The Fault Condition is related to which technology?
A. BGP
B. NAT
C. IP NAT
D. IPv4 OSPF Routing
E. IPv4 OSPF Redistribution
F. IPv6 OSPF Routing
G. IPv4 layer 3 security
Answer: C
What is the solution of the fault condition?
A. Under the interface Serial0/0/0 configuration enter the ip nat inside command
B. Under the interface Serial0/0/1 configuration enter the ip nat outside command
C. Under the ip access-list standar nat_trafic configuration enter the permit 10.2.0.0 0.0.255.255 command
D. Under the ip access-list standar nat_trafic configuration enter the permit 209.65.200.0 0.0.0.255 command
Answer: C
The Fault Condition is related to which technology?
A. BGP
B. NTP
C. IP NAT
D. IPv4 OSPF Routing
E. IPv4 OSPF Redistribution
F. IPv6 OSPF Routing
G. IPv4 layer 3 security
Answer: A
Speaking of Cisco 300-135 exam, Passtcert cisco 300-135 tshoot braindump have been ahead of other sites. Because Passtcert has a strong IT elite team, they always follow the latest cisco 300-135 tshoot braindump, with their professional mind to focus on cisco 300-135 tshoot braindump.Passtcert is a website that provide the counseling courses for IT professionals to participate in Cisco certification 300-135 exam and help them get the Cisco 300-135 certification.Sponsor Ads
About Gregor Yedell 
Actual Exam Questions And Answers
52 connections, 0 recommendations, 271 honor points.Joined APSense since, April 26th, 2016, From JIESTWYU, United States.
Created on Oct 23rd 2017 03:21. Viewed 351 times.
Comments
No comment, be the first to comment.
