Articles
Through-Hole - Why It is Still Relevant in PCB Designs?
by Abby12345 Hao Pcb engineerWhen it comes to the manufacturing of electronic components, the PCB plays a vital part in its quality and usability. The ultimate functionality of a PCB depends on the design used to make it, and as we are going to discuss, there are two widely used designs: Through-Hole technology and the Surface Mount Technology.
Our primary focus on this article will be the Through-Hole technology, and we will go into detail as to why it is prevalent in the manufacture of electronics.
1、What is Through-Hole Technology?
It is a mounting technique where the leads and chips of electronic components are inserted Through-Holes on the printed circuit board. Here, these pins undergo soldering from beneath to pads on the opposite sides of the board. This technique is usually done by hand or sometimes by insertion mounts machines. This technology thrived well until the late 1980s with the introduction of the surface mount technology (SMT) capping it down. With the introduction of the surface mount, it was expected that the Through-Hole would be obsolete, but it has stood the test of time with is numerous and distinctive advantages as well as its reliability.
2、Through-Hole leads
PCBs that use Through-Hole have wire leads that come in two types: radial or axial leads.
2.1.Axial
The axial leads are similar in shape as wire jumpers, and they protrude from the tip end of either boxed-shaped or cylindrical components of the PCB. These protrusions will form almost a perfect geometrical axis of symmetry. Even though they protrude, it is not much above the surface of the PCB, making it a flat configuration if placed down.
Axial leads are commonly used to bridge short distances on a PCB while also spanning point to point wiring that open space does not support.
2.2.Radial
The radial name comes from their parallel projection of the leads from the components to the surface board, and radial leads are in sync with the ends of the packages. Before, they were identified because they took the shape of the radius of the cylindrical components that they protruded over, but the axial leads later nullified this definition.
Onboard, the radial components have a 90 degrees angle formation with a lesser footprint as compared to the axial leads. They also possess a plugin nature due to their parallel composition, making them a considerable lead of choice to use in components that require higher speeds of automation.
3、Through-Hole Soldering
Well, soldering is one of the necessary skills you need if you are to venture into the world of electronics. Knowing your way around a PCB board with what needs to undergo replacement and where is very crucial. Though, when it comes to repairing boards that use through-hole technology, a lot of precision comes into place.
3.1.Advanced PTH
Assuming you have the necessary soldering skills at your fingertips, then you could opt for the Advanced PTH technique for your soldering. Let’s dive and see some of the essential tips you need to learn.
1. Learn to control how the solder flows. This skill is the first thing you will learn, though, with time and practice, you will get it right.
2. Learn to use and control different tips of the soldering gun. That is because various applications will require separate tips, and you ought to know how to use them.
3. Once you have decided a gun to use, heat the lead and the pad and let the solder flow smoothly through the hole on the board.
4. Let the soldering iron cool; then, you will have your connection ready.
5. You can use this technique when also creating bridges between two Through-Holes.
3.2. Cleaning
Once you have performed your soldering, it is crucial to know how to clean it. What do we clean, some might ask? Well, when dealing with lead-free solder, you tend to mess up your PCB with flux. This flux can be from the soldering iron itself or when you choose to apply flux intentionally to avoid wrong connections. So, how do we go about this?
The best and recommended way is by the use of a small toothbrush that you dip or spray with isopropyl alcohol and brush the board. But if you are working on many boards and you run the risk of having the flux dry on the boards, then you could fill a crockpot with distilled water. The distilled water will ensure that no impurities are within the circuit.
4、Advantages of Through-Hole Technology
The through-hole technology is impressive even though it has been there over time, and newer technologies might replace it. What are the reasons that make it still a desired technology over the surface mount? Let's have a look at the advantages of this technology to PCB designs.
4.1.Sturdy
Through-hole components prove to be a real gold mine when it comes to their durability and how effective they are when it comes to products that will require secure connections in its layers.
So in case you are working on a PCB board with this technology, you will notice that no matter what environmental stress that you expose it to, they will remain in contact. It is because through-hole components are reinforced when they run through the board as compared to SMT components that are only soldered on the PCBs.
With this aspect, they are commonly used in military and aerospace electronics since they can endure extreme variable conditions.
4.2.Stronger mechanical bonds
Through-hole technology works perfectly well for components that are heavier or bulkier in their composition. It is considerable because they require stronger bonds mechanically in their PCBs, which ordinary Surface Mount Technology will not possibly offer to these electronics.
4.3.Easier prototyping
With the Through-Hole technology, designers have an easier time because of their convenience in manual replacement and adjustment capabilities. Through board also uses breadboard sockets, which are essential in prototyping.
5、Constraints Related to Through-Hole Technology
Even though Through-Hole technology stands as a very unique and enticing technology, even after surface mount, it still has a few drawbacks. The technology is not practical for higher speed components that might need a small stray in capacitance and inductance for its wire leads.
5.1.Takes up more board real-estate
Once you opt for the Through-Hole technology, a lot of your board space will have to service the lodge of the wire leads, making you have to invest in a larger PCB. The bigger PCB reduces the essence of trying to minimize all the wiring and cutting the board to a generally workable size.
6、Surface Mount Technology (SMT)
The surface mount technology is always associated with the Through-Hole though they are uniquely distinct. This technology works by lodging the leads of the components to the board directly through soldering, and no drilling whatsoever happens. Unlike Through-Hole, this technology is quite easy for designers to create. It was revolutionary because of its comparatively lower prices to produce and manufacture, as well as because all previous electronics, most can now adopt this technology.
7、Conclusion
The current state of things is that, even though the two designs seem like in constant completion, they are both widely used in the manufacture of electronics. So, this ultimately ends up to what is your desire as an electronics enthusiast, or what sort of electronics you are handling. When it comes to repair and soldering of the Through-Hole boards, as discussed earlier, a lot of precision should be in place to ensure that the pins of the leads firmly fit and ensure that you have a tight grasp of the components to be soldered.
Learn more about PCB assembly, get started!
Sponsor Ads
About Abby12345 Hao 
Pcb engineer
5 connections, 0 recommendations, 21 honor points.Joined APSense since, April 4th, 2019, From shijiazhuang, China.
Created on Nov 4th 2019 04:16. Viewed 310 times.
