Articles

How to use Consult 3 Plus to add Nissan Altima 2006 remote key?

by Alex Carter Mechanic Assistant
This is how to decode & cut a key and program or add a new key to Nissan Altima year 2006.

If you have all remotes available:

Here, you must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.

  1. Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
  2. Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
  3. Insert key into ignition and turn to the ACC position.
  4. Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
  5. If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
  6. When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.

If you have a decent key only or lose all keys:

You need:
a decent auto programming tool for the car: Nissan Consult 3 or Consult 3 plus
security immobilizer card used to make keys to Nissan
a good automatic key cutter, such as SEC-E9 key cutting machine
and good new keys/remotes to add


The steps:

read pin – program key – decode and cut keys

in detail…

Step 1: NSPC001 reads pin codes

Connect the code reader into the OBD diagnostic socket
Read the 5-digit BCM code and transfer it to 4-digit pin code
Write down the pin code
Disconnect the pin code reader

Step 2: Nissan Consult 3 plus adds new keys

Connect Consult III plus to the computer and the vehicle
Connection method: via the USB cable or Bluetooth
Insert key into the key hole, turn ignition ON with engine OFF
Start Consult-III plus software
Click on “Connect” button on VIMI selection screen to connect with VI
nissan-consult-3-plus-add-key-1
the computer and vehicle establish good communication
then Consult3 plus software will display VIN info
Choose Nissan model and year, and confirm vehicle information
nissan-consult-3-plus-add-key-2
Wait until the Nissan Consult module to access all control modules, Engine, BCM, Transmission, Airbag etc.
The car dashboard will illuminate and the indicator lights on Consult 3 will flash
nissan-consult-3-plus-add-key-3
Diagnostic: Direct Diagnostic Mode program
Tick Key programming icon (NATS SELECT DIAG MODE) on the left menu, plug the security card and press START
(There are two options under NATS SELECT DIAG MODE. Select C/U INITIALIZATION.
nissan-consult-3-plus-add-key-4
Push START BUTTON after enter password
Manually enter the pin code
Initialization completed
Follow the guide in the sw to finish key programming

Step 3: SEC-E9 machine decodes and cuts Nissan keys

First decoding…then cutting….

Car BrandModelYearIC Card
NissanJuke2010-09022
NissanX-Trail2007-06132
NissanX-Trail2007-06133
NissanVersa2007-06135
NissanVersa2007-06136
NissanTidaLatio2004-06137
NissanTida2004-20126138
NissanSkyline1999-20066139
NissanSentra2007-20096140
NissanSentra2007-20096141
NissanRogue2007-06142
NissanRogue2007-06143
NissanQashqai2007-06144
NissanQashqai2007-06145
NissanPixo2008-06146
NissanPatrol2007-06147
NissanPathfinder2005-06148
NissanNote2006-06149
NissanNote2006-06150
NissanNavara2005-06151
NissanNavara2005-06152
NissanMurano2009-06153
NissanMurano2009-06154
NissanMicra2007-06155
NissanMicra2007-06156
NissanMaxima2007-06157
NissanMarch2003-20076158
NissanMarch2003-20076159
NissanGTR2007-06160
NissanElgrand1997-20026161
NissanElgrand2002-20106162
NissanCube2002-20086163
NissanCube2009-06164
NissanCabstar2000-06165
NissanAtlas Truck2007-06166
NissanArmada2008-06167
NissanArmada2008-06168
Nissan140Y1973-19784770
Nissan140Y1973-19784771
Nissan140Y1978-19824772
Nissan140Y1978-19824773
Nissan160J1978-19824774
Nissan160J1978-19824775
Nissan180B1971-19764776
Nissan180B1971-19764777
Nissan180SX1989-19944778
Nissan180SX1995-19994779
Nissan200B1976-19804780
Nissan200B1976-19804781
Nissan200SX1984-19884782
Nissan200SX1995-19984783
Nissan200SX (North America)1984-19884784
Nissan200SX (North America)1995-19984785
Nissan200ZR1983-19894786
Nissan2101978-19824787
Nissan2101978-19824788
Nissan240C1975-19794789
Nissan240C1975-19794790
Nissan240C1979-19844791
Nissan240C1979-19844792
Nissan240K1977-19814793
Nissan240K1977-19814794
Nissan240SX1989-19944795
Nissan240SX1995-19984796
Nissan240SX (North America)1989-19944797
Nissan240SX (North America)1995-19984798
Nissan240Z1970-19764799
Nissan240Z1970-19764800
Nissan260C1975-19794801
Nissan260C1975-19794802
Nissan260C1979-19844803
Nissan260C1979-19844804
Nissan260Z1970-19764805
Nissan260Z1970-19764806
Nissan280C1975-19794807
Nissan280C1975-19794808
Nissan280C1979-19844809
Nissan280C1979-19844810
Nissan280Z1976-19784811
Nissan280Z1976-19784812
Nissan280ZX1979-19834813
Nissan280ZX1984-19964814
Nissan300C1983-19874815
Nissan300ZX1979-19834816
Nissan300ZX1983-19894817
Nissan300ZX1990-19964818
Nissan300ZX1997-19994819
Nissan3101979-19834820
Nissan

Sponsor Ads


About Alex Carter Advanced   Mechanic Assistant

45 connections, 0 recommendations, 438 honor points.
Joined APSense since, July 23rd, 2015, From Carlifornia, United States.

Created on Apr 10th 2019 01:15. Viewed 438 times.

Comments

No comment, be the first to comment.
Please sign in before you comment.