How to Resolve the USB Flash Drive No Response Problem
by Mike Parflia18 My SkyDuring data storage devices, USB flash drive is very important in
transferring and storing data because USB flash drives are typically
removable and rewritable, and physically much smaller than a floppy
disk. If the USB flash drive has some problems, such as formatting,
deleting, virus infection and other reasons, you can’t open and use USB
flash drive, you probably loss the data storaged in it. If you are a Mac
user, you can use this hard drive data recovery software (click here)
to recover Mac data from Macintosh hard drive, iPod, USB drive, SD
card, digital camera, mobile phone, MP3, and MP4 player due to deleting,
formatting, virus infection, improper operation, unexpected power
failure, and other unknown reasons. It can recover hard drive on Mac with high quality and save your precious time.
But sometimes it is not necessary to use a data recovery software, you
can resolve the problem by yourself. When the USB flash drive errors
happen, first to exclude normal damage to the USB interface and PCB
Weld, and USB extension cable, and then repair by following guides.
1. USB flash disk doesn’t response to machine.
(1) power supply is divided into the main required to supply and FLASH
needed to supply these two is the key, USB flash disk circuit is very
simple, such as power supply are generally insurance inductance damage
or 3.3 V voltage regulator block is damaged, it comes to the regulator
block here, three-pin power input (5V), ground, power output (3.3), the
working principle is that when the input pin input is a 5V voltage
output pin will output a stable 3.3V. As long as you find out where the
power stops, the problem will be solved well.
(2) Clock master in a certain frequency can work with FLASH
communication but also the clock signal for transmission, so if the
clock signal, the master will definitely not work. Circuit check this
regard when, in fact, the clock generation circuit is very simple, only
need to check the crystal and its peripheral circuits can be crystal
afraid brush USB flash disk compact and very easy to fall to the ground
causing crystal damage, as long as the replacement of the same crystal
can. Note: The crystal oscillator can not be measured to determine the
best way to good or bad is the substitution of a good crystal to
determine.
(3) If the above two conditions are normal and that it is
because the main chip is damaged, then you have to replace the master.
2. USB flash disk is inserted to computer, it says "unrecognized device".
Maintenance ideas: in this case, you can get the first note that USB
flash disk circuit is normal, it is only the communication problem with
computer. You should check out the following:
(1) USB flash disk
interface circuit. The circuit without any special component is the two
data lines D + D-, so check this circuit, as long as the measurement
data line to the line between the master normal to, the general in the
data two small resistor between the lines and the main control circuit
connected in series, to play a role in protection, so you want to check
whether these two resistor.
(2) Clock circuit. Due to the USB flash drive has to be consistent with
computer, if the operating frequency of the USB flash disk and the
computer can not sync, then the system will think this is an
"unrecognized device". At this time we should change the crystal.
(3) The master. If the above two checks are normal, it can determine the
master damaged. Prompt "Please insert the disk, the computer prompts:"
Please insert a disk into drive H "prompt Format to open the USB flash
disk which are garbled, capacity does not match.
Maintenance ideas:
for this phenomenon can be judged that the USB flash disk hardware has
no problem, it is just the software problems.
Solution: you need to
find a repair tool to fix the master program. This is necessary depends
on what program does the USB flash disk master uses.
USB flash the
disk failure is probably the main problems. Other problems like can’t be
written or storage any data, this is mainly due to the USB flash
drive’s bad performance or bad blocks.
Go on reading: How to Recover Data on Mac?
Sponsor Ads
Created on Dec 31st 1969 18:00. Viewed 0 times.