Garage Door Opener Repair Guide

If your garage door opener not working you are in the right place as we will discuss how to repair it. This guide can help you do that by yourself instead of hiring a professional service which can cost you a lot. However, if the issue still persists after getting through this guide you should need to consult a professional.

Without further ado let’s check out the guide.

The first thing you need to check out is if the remote is working If the remote working is you need to check the wall switch. If the wall switch is not working you need to check the wall switch by opening it. The wall switch can be faulty or the wires connecting it can be faulty. You can check the wires by opening them and connecting them together if there is electricity then it means the wires are fine and you need to replace the wall switch. However, if there is no electricity in the wires then the wires are faulty and you need to fix them. You can get the wall switch for just 15 dollars from the hardware store. It is cheaper to replace the wall switch.

The second issue you can face is that the wall switch works but the remote is not working. You have to check the batteries of the remote if they work then check the remote again. If the remote still does not work you need to replace it. However, if you can’t find the remote for your current model you can get the universal remote. Also, you can replace the receiver with a new one and can get a remote for that. The new receiver comes with a PIN code and allows you to have peace of mind that no one can steal or open the garage door without your permission.

Another troubleshooting you can do is check the light sensors. If the door goes up and does not get down you need to check the sensors thoroughly. You need to check the safety sensors if they are aligned or not. If the light blinks and safety sensors work you need to look another way. If the safety sensors do not light up you need to replace them.

The garage door opener does not work due to the bad circuit can be an issue if you use the remote and switch and there are no lights you can consider that the circuit has gone bad. It can be scary for some people to change the circuit board but it is not a difficult task. You can replace the circuit board by having the ¼ inches nut driver. All you have to do is replace the circuit board you can do it by yourself by following these instructions. First, take off the light cover then take out the bulb and remove the safety sensor wires and switch wires. Remove the screws and you can take out the circuit board yourself. The new circuit board costs around $80 so get the new one and also buy the power surge protector it will not cost you more than 10 dollars. So, the power surge protector protects the circuit board and you can live in peace.

Another issue that can you face with the garage door opener is that everything is working fine but the lights are not working. You can change the light bulb by removing the circuit board. As we already mentioned the way to remove the circuit board we don’t have to repeat it. All you have to do is to replace the light bulb. Ensure that you get the right wattage of the bulb rated with the circuit board. If you end up having a higher-wattage bulb it can become a fire hazard and it won’t work. So, ensure that the wattage of the bulb is right and according to the circuit board.

Another issue you can face and fix is that the trolley carriage moves but the door does not open. The issue can be the trolley carriage you need to replace it. You can do that by hanging the door with a chain. You need to make sure that the chains are tightened. Now it's time to remove the old trolley carriage and replace it with the new one. Once the chain is placed remove the trolley from both sides and replace it with the new one. The trolley is not very expensive and can cost you around 10 dollars to 25 dollars depending on the model of your garage door opener.

Another way to fix your door opener is to check that the door is working fine. However, you can face the issues like the garage door not opening. You can fix that issue by lubricating the rails. You should lubricate the rails when it comes in contact with the trolley. Use a lubricant that does not attract the dirt and debris. You can use silicon spray for that purpose. You should lubricate the rails and trolley once or twice a year to avoid these types of issues. If you live in a colder place then we recommend using the lithium grease as it won’t get hard when the temperature decreases.

Conclusion

So these are the few things that you can look by yourself if the garage door opener is not working. You can troubleshoot the issues by yourself by following this guide. However, if the process is beyond your control you can hire the professional services. But know that hiring a professional will cost you more. If you are Do it yourself person than you should do it by yourself. There can be many issues that cannot be controlled so, always look out for the garage door opener.

Know that there can be issues that are beyond you and you will need to hire professional ones. However, if you feel confident that you can do it then do it by yourself it will save you money. We have mentioned the most common issues in this article that cause the garage door opener won’t work but there can be some other issues which are not covered in this article. If you are looking for a Garage Door Expert in Ottawa area do give A1 Garage Doors a call at 343-309-9964

Sponsor Ads

• Ad Space Available - Rent it Now!

Report this Page

Created on Sep 4th 2023 15:57. Viewed 183 times.

Share on APSense

Comments