E20-542 Test Certification

Test Information:

Total Questions: 136

Test Number: E20-542

Vendor Name: EMC

Cert Name:  EMCTA

Test Name: VMAX3 Solutions and Design Specialist Exam for Technology Architects

Official Site: http://www.examsboost.com

For More Details: http://www.examsboost.com/test/E20-542/

Question: 1              

 

A customer wants to configure a large SRDF deployment between two VMAX3 arrays. The customer has many different applications and workloads. They want to separate each into its own SRDF group.

What is the maximum number of SRDF groups this configuration will support?

 

A. 64

B. 96

C. 184

D. 250

 

Answer: D                   

 

Question: 2              

 

Which legacy TimeFinder technologies are supported by TimeFinder SnapVX emulation mode?

 

A. Mirror, Clone, VP Snap

B. Mirror, Clone, Snap

C. Mirror, VP Snap, Snap

D. Clone, VP Snap, Snap

 

Answer: A                   

 

Question: 3              

 

What is the maximum number of linked targets that TimeFinder SnapVX supports?

 

A. 32

B. 128

C. 256

D. 1024

 

Answer: D                   

 

Question: 4              

 

Where will TimeFinder SnapVX snapshot deltas be stored on a VMAX3 array?

 

A. Storage Resource Pool

B. Dedicated Target Device

C. Reserved LUN Pool

D. Array Cache

 

Answer: A                   

 

Question: 5               

 

A customer has production and disaster recovery VMAX3 arrays. There is limited bandwidth between the sites. The amount of data which will be replicated by using SRDF to the disaster recovery site is slightly more than the available bandwidth allows.

Which action is needed to accommodate the customer’s need?

 

A. Install an optional compression module

B. Enable the compression license

C. Enable compression on the RA Director

D. Enable the Fast Write feature on the SRDF Group

 

Answer: A                   

 

Question: 6              

 

A customer is using two VMAX3 arrays with a compression module installed on both arrays. After careful monitoring of the SRDF traffic, they discover that the data is not being compressed.

What additional action needs to be performed to enable compression?

 

A. Enable compression at the SRDF Group level

B. Enable compression at the RA Director level

C. Enable the compression license

D. Enable compression on the engine containing the RA Director

 

Answer: A                   

 

Question: 7              

 

You have configured Open Replicator between a new VMAX3 array and a VMAX. A host is connected to the VMAX3 array and a control device is configured to pull data from a remote device on the VMAX. You want the host to be able to access data on the control device while the data is being pulled from the remote device.

What will cause writes to the control device to be propagated back to the remote device?

 

A. Donor Update

B. Copy-On-First Access

C. Front-end Zero Detection

D. Background Copy

 

Answer: A                   

 

Question: 8              

 

A customer needs to automate SRDF disaster recovery for a Microsoft cluster. Which SRDF solution is recommended?

 

A. SRDF/CE

B. SRDF/DM

C. SRDF/CG

D. SRDF/AR

 

Answer: A                   

 

Question: 9              

 

When data consistency is not a requirement, which SRDF mode is preferred when replicating large volumes of data?

 

A. SRDF/DM

B. SRDF/A

C. SRDF/S

D. SRDF/CG

 

Answer: A                   

 

Question: 10              

 

The Reserved Capacity for a Storage Resource Pool (SRP) on a VMAX3 has been set to 15%. A TimeFinder SnapVX snapshot has been created for a Storage Group containing 10 devices. An application is actively performing read and write I/Os to these devices. Allocation for the SRP reaches 85%.

What will happen to the snapshot?

 

A. Snapshot will fail

B. Snapshot deltas will be allocated from the Reserved Capacity

C. Snapshot will persist but new snapshot deltas cannot be created

D. Snapshot will terminate

 

Answer: A