CCNP TSHOOT 300-135 practice test|CertTree

by Karen Paramo IT sales consultant

Troubleshooting and Maintaining Cisco IP Networks (TSHOOT 300-135) is a 120-minute qualifying exam with 15‒25 questions for the Cisco CCNP Routing and Switching certification. The TSHOOT 300-135 exam certifies that the successful candidate has the knowledge and skills necessary to:

• Plan and perform regular maintenance on complex enterprise routed and switched networks
• Use technology-based practices and a systematic ITIL-compliant approach to perform network troubleshooting

CertTree CCNP TSHOOT 300-135 practice test|CertTree gives you the experience of actual Cisco 300-135. We know exactly what is needed and have all the study notes, real exam questions, 300-135 test questions included in real Cisco certification 300-135 test. Our CCNP TSHOOT 300-135 practice test|CertTree covers over 96% of the questions and answers that may be asked in your Cisco 300-135 exam. Every point from CertTree CCNP TSHOOT 300-135 practice test|CertTree will help you take 300-135 exam easier and become Cisco Certification certified in a short time.

Share some CCNP 300-135 exam questions and answers below.
Which command will limit debug output ppp authentication on serial 0/1 and serial 0/2?
A. debug condition interface range s0/1 -0/2
debug ppp authentication
B. debug condition interface s0/1 & 0/2
debug ppp authentication
C. debug int s0/1
debug int 0/2
debug ppp authentication
D. Debug condition interface s0/1
Debug condition interface s0/2
debug ppp authentication
Answer: D

Ticket 5 R1ACL

TROUBLE TICKET STATEMENT:
The implementation group has been using thetest bed to do a ¡®proof-of-concept¡¯that required both client 1 and client 2 to access the Web Server at 209.65.200.241.After several changed to interface status, network addressing, routing schemes and layer 2 connectivity, at trouble ticket has been opened indicating that client 1 cannot ping the 209.65.200.241 (internet Server).
show run by yourself to obtain the following information:
Client 1 is not able to reach the WebServer at 209.65.200.241. Initial troubleshooting shows that R1 is also not able to reach the WebServer. R1 also does not have any active BGP neighbor.
Configuration on R1
! interface Serial0/0/0/1
description link to ISP
ip address 209.65.200.224 255.255.255.252
ip access-group edge_security in
ip nat outside
ip virtual-reassembly
ntp brasdcast client
net broadcast key 1
no cdp enable
!! ip access-list nat_traffic permit 10.1.0.0 0.0.255.255
ip access-list nat_traffic permit 10.2.0.0 0.0.255.255
! ip access-list edge_security deny ip 10.0.0.0 0.255.255.255 any
ip access-list edge_security deny ip 172.16.0.0 0.15.255.255 any
ip access-list edge_security deny ip 192.168.0.0 0.0.255.255 any
ip access-list edge_security deny ip 127.0.0.0 0.255.255.255 any
ip access-list edge_security permit ip host 209.65.200.241 any

On which device is the fault condition located?
A. R1
B. R2
C. R3
D. R4
E. DSW1
F. DSW2
G. ASW1
Answer: A


R1 and R2 OSPF neighbor.
Which two statements are true? (Choose two)
(Output from show ip ospf neighbors on 2 routers, one of them shows FULL/DR, the other FULL/-, you need to know how were they configured and will they exchange routes)
A. They are not neighbors
B. R1 (non-DR) will not update its routes to R2
C. Router R2 is configured with ospf point-to-point command (R2 is the router that shows as FULL/-)
D. They need to be configured as OSPF NBMA
E. R2 should be configured as stub
Answer: BC

The Fault Condition is related to which technology?
A. BGP
B. NAT
C. IP NAT
D. IPv4 OSPF Routing
E. IPv4 OSPF Redistribution
F. IPv6 OSPF Routing
G. IPv4 layer 3 security
Answer: C

The fault condition is related to which technology?
A. NTP
B. IP DHCP Server
C. IPv4 OSPF Routing
D. IPv4 EIGRP Routing
E. IPv4 Route Redistribution
F. IPv6 RIP Routing
G. IPv6 OSPF Routing
H. IPV4 and IPV6 Interoperability
I. IPv4 layer 3 security
Answer: G

What is the solution of the fault condition?
A. Under the ip access-list edge_security configuration add the permit ip 209.65.200.224 0.0.0.3 any command
B. Under the interface Serial0/0/1 enter the ip access-group edge_security out command.
C. Under the ip access-list edge_security configuration delete the deny ip 10.0.0.0 0.255.255.255 any command
D. Under the interface Serial0/0/0 configuration delete the ip access-group edge_security in command and enter the ip access group edge_security out command
Answer: A

What is the MTU¡¯s size in a GRE tunnel?
A. 1630
B. 1476
C. 1500
D. 1900
Answer: B

The Fault Condition is related to which technology?
A. BGP
B. NAT
C. IP NAT
D. IPv4 OSPF Routing
E. IPv4 OSPF Redistribution
F. IPv6 OSPF Routing
G. IPv4 layer 3 security
Answer: C


How to check MTU of interface using ping? / How can you check the links mtu size with ping command?
A. ping 10.1.1.1 size 1501
B. ping 10.1.1.1 size 1500 df-bit
C. ping 10.1.1.1
D. ping 10.1.1.1 no-size
Answer: B

What is the solution to the fault condition?
A. Under the interface Tunnel34 configuration enter the ipv6 ospf 6 area 34 command.
B. Under the interface Loopback6 configuration enter the ipv6 ospf 6 area 34 command.
C. Under the interface Serial0/0/0.34 configuration enter the ipv6 ospf 6 area 34 command.
D. Under ipv6 router ospf 6 configuration enter the redistribute rip RIP_ZONE include-connected command.
Answer: D

What is the solution of the fault condition?
A. Under the interface Serial0/0/0 configuration enter the ip nat inside command
B. Under the interface Serial0/0/1 configuration enter the ip nat outside command
C. Under the ip access-list standar nat_trafic configuration enter the permit 10.2.0.0 0.0.255.255 command
D. Under the ip access-list standar nat_trafic configuration enter the permit 209.65.200.0 0.0.0.255 command
Answer: C


The Fault Condition is related to which technology?
A. BGP
B. NAT
C. IP NAT
D. IPv4 OSPF Routing
E. IPv4 OSPF Redistribution
F. IPv6 OSPF Routing
G. IPv4 layer 3 security
Answer: G

What is the solution of the fault condition?
A. Under the BGP process,enter the bgp redistribute-internal command
B. Under the BGP process, bgp confederation identifier 65001 command
C. Delete the current BGP process and reenter all of the commands using 65002 as theAS number.
D. Under the BGP process, delete the neighbor 209.56.200.226 remote-as 65002 command enter the neighbor 209.65.200.226 remote-as 65002 command.
Answer: D


The Fault Condition is related to which technology?
A. BGP
B. NTP
C. IP NAT
D. IPv4 OSPF Routing
E. IPv4 OSPF Redistribution
F. IPv6 OSPF Routing
G. IPv4 layer 3 security
Answer: A


The tunnel between R1 and R3 is not coming up. Which two statements are true? (Choose two)
(Topology with a GRE tunnel and the outputs provided are show ip int brief and tunnel source and destination)
A. Tunnel source int Eth0/0 is down
B. No route from R1 to R3 loopback0 (tunnel destination)
C. source and destination not in same subnet
D. http://bbs.hh010.com/
Answer: AB

Do you want to pass the Cisco 300-135 exam better and faster? Then please select the CertTree. It can help you achieve your dreams. CertTree is a website that provide accurate CCNP TSHOOT 300-135 practice test|CertTree for people who want to participate in the IT certification. CertTree can help a lot of IT professionals to enhance their career blueprint. Our strength will make you incredible. You can try a part of the questions and answers about Cisco 300-135 exam to test our reliability.

Sponsor Ads

• Ad Space Available - Rent it Now!

Created on Oct 15th 2017 22:46. Viewed 394 times.

Comments