What is a swing turnstile

The swing turnstile is generally called a flapping gate in the rail transit industry. The shape of its blocking body (swing turnstile) is a plane with a certain area, which is perpendicular to the ground, and can be blocked and released by rotating and swinging. The materials of the blocking body are commonly used stainless steel, plexiglass, and tempered glass, and some of them also use metal plates to cover special flexible materials (to reduce the injury of impacting pedestrians). The shape of the blocking body (swing pendulum) is a plane with a certain area, which is perpendicular to the ground, and can be blocked and released by rotating and swinging. The swing turnstile is composed of chassis, movement, swing arm, control system, infrared sensor, control equipment and other parts. The swing turnstile is suitable for occasions that require a relatively large channel width, including occasions where there are many pedestrians or bicycles carrying luggage and packages, and special channels for people with disabilities. Compared with other types of pedestrian gates, the swing turnstile has the following three advantages: 1. There is no mechanical collision during the operation of the gate swing, and the noise is relatively small. 2. Compared with the three-roller gate, the bridge swing turnstile has a pedestrian passing detection module, which can effectively detect the passing target and has a strong anti-tailing ability. 3. The channel width is the largest among all turnstiles, generally between 550mm and 1000mm, and some high-end products can reach 1500mm, which is more suitable for pedestrians or bicycles carrying luggage and packages, and can also be used for people with limited mobility. dedicated channel. And what's more,it is easy to design a very beautiful shape, so it is often used in office buildings, smart buildings, clubs and other high-end occasions . Although there are many advantages of swing turnstiles, you must pay attention when choosing swing turnstiles. Because swing turnstiles have relatively high technical requirements on manufacturers, if the design is not good, it will greatly reduce the reliability of the product and reduce the anti-pinch protection to avoid personal injury. The ability to hit people. The precautions when installing the swing turnstile are as follows: 1. Prepare the tools used to install the swing turnstile in advance, and check the accessories of the swing turnstile according to the packing list. 2. Before starting the installation, it is necessary to clarify the system composition and working method of the swing turnstile, and then carry out the overall planning and installation. 3. After the foundation surface is treated, arrange the swing turnstile equipment in sequence. 4. After determining the hole position of the swing turnstile, drill the hole, and pre-embed M12 anchor bolts or expansion bolts. 5. Use 3/4″ PVC conduit to wear the strong current cable and weak current cable in turn and bury them in the corresponding position. 6. Move the chassis of the swing turnstile to the corresponding installation positions in turn, and align the anchor bolt positions one by one. 7. Check whether the composition and working method of the swing turnstile are placed correctly, and then proceed to the next step after checking if there is no problem. 8. Refer to the wiring diagram of the swing turnstile, and connect the power line and control line of the swing turnstile respectively. Remember to connect the system protection ground wire. 9. After the state and function of the swing turnstile have been debugged, tighten the fixed nut. The swing turnstile is generally called a flapping gate in the rail transit industry. The shape of its blocking body (swing turnstile) is a plane with a certain area, which is perpendicular to the ground, and can be blocked and released by rotating and swinging. The materials of the blocking body are commonly used stainless steel, plexiglass, and tempered glass, and some of them also use metal plates to cover special flexible materials (to reduce the injury of impacting pedestrians). The shape of the blocking body (swing pendulum) is a plane with a certain area, which is perpendicular to the ground, and can be blocked and released by rotating and swinging. The swing turnstile is composed of chassis, movement, swing arm, control system, infrared sensor, control equipment and other parts. The swing turnstile is suitable for occasions that require a relatively large channel width, including occasions where there are many pedestrians or bicycles carrying luggage and packages, and special channels for people with disabilities.