Articles

RTJ Gaskets/Ring Joint Gaskets By yaang.com

by yane Yang Sales Manager
Yaang's Ring Joint Gaskets are precision machined, metallic sealing rings suitable for high pressure and high temperature applications. RTJ gaskets are designed to seal by "initial line contact" or wedging action between the mating flange and the gasket. By applying pressure on the seal interface through bolt force, the softer metal of the gasket flows into the micro-fine structure of the harder flange material, creating a very tight and efficient seal.

Yaang's Ring Joint gaskets are manufactured in accordance with API-6A and ASME B16.20 specifications and come in four basic profiles:

R-Oval - Ring Gasket


Style R ring joint gaskets are manufactured in accordance with both API 6A and ASME B16.20 size/ratings. Available in both oval and octagonal configurations, both types are interchangeable on modern octagonal type grooved flanges.
Style R Ring Joint gaskets can be manufactured in accordance with all relevant standards to suit the following flange designations: API- 6A, ASME/ANSI B16.5, MSS SP44 (ASME B 16.47 Series A) & BS 1560. 
Tolerances: (Inches)
Width of Ring .......................................±0.008
Height of Ring ......................................±0.020
Pitch Diameter ......................................±0.007

R-Octagonal - Ring Gasket


Style R octagonal ring joint gaskets are manufactured in accordance with both API 6A and ASME B16.20 size/ratings. Available in both oval and octagonal configurations, both types are interchangeable on modern octagonal type grooved flanges.
Style R Ring Joint gaskets can be manufactured in accordance with all relevant standards to suit the following flange designations: API- 6A, ASME/ANSI B16.5, MSS SP44 (ASME B 16.47 Series A) & BS 1560. 
Tolerances: (Inches)
Width of Ring .......................................±0.008
Height of Ring ......................................±0.020
Pitch Diameter ......................................±0.007
Angle of 23° ......................±1/2°

RX - Ring Gasket


Style RX RTJ gaskets are a pressure-energized adaptation of the standard Style R gasket. The RX is designed to fit the same groove design as a standard Style R, making the joints interchangeable. The modified design uses a pressure-energized effect that improves the efficiency of the seal as the internal pressure of the system increases.
Tolerances:(Inches)
Width of Ring ........................................+0.008,-0.000
Height of Ring .......................................+0.008,-0.000
(A plus tolerance of 0.008 inches for width and height is permitted, provided the variation in width or height does not exceed 0.004 inches throughout its entire circumference)
OD of Ring ............................................±0.020,-0.000
Angle of 23°…………................................±1/2° 
Note: Only Rings RX82 through RX91 have a pressure passage hole through the cross section. Center line of hole is located on the mid-point of the width flat. 
Hole diameter shall be as follows:
RX82 through RX85...............................0.06”
RX86 and RX87......................................0.09”
Rings RX88 through RX91......................0.12”

BX - Ring Gasket


Style BX ring joint pressure energized gaskets are manufactured in accordance with API 6A and are designed for use on pressurized systems up to 20,000 PSI.
When correctly fitted, the style BX gasket allows virtual surface-to-surface contact of the flange faces, which means that the gasket is fully trapped on both the inner and outer diameters.
All BX gaskets incorporate a pressure balance hole to ensure equalization of pressure that may be trapped in the grooves.
Tolerances:(Inches)
Width of Ring .......................................+0.008,-0.000
Hole Size ..............................................±0.02
Height of Ring ......................................+0.080,-0.000
OD of Ring ............................................+0.000,-0.006
Angle of 23° .........................................±1/4° 
One pressure passage hole required per ring on centerline. A plus tolerance of 0.008 inches for width of ring and height of ring is permitted, provided the variation in width or height does not exceed 0.004 inches throughout its entire circumference.
NOTE: Radius of the ring shall be 8% to12% of the ring height.


These basic shapes are used in a variety of applications with pressures up to 20,000 PSI. The dimensions are standardized and require specially grooved flanges by where a corresponding "R" or "BX" number is assigned for pipe size and pressure class for gasket identification.

To ensure cost effectiveness and reliability, Yaang's CNC automation and state-of-the-art coordinate measuring systems provide reliable benchmarks for our on-going quality control operations.

Source: Zhejiang Yaang Pipe Industry Co., Limited (www.yaang.com)


Sponsor Ads


About yane Yang Senior     Sales Manager

144 connections, 0 recommendations, 658 honor points.
Joined APSense since, June 7th, 2014, From wenzhou, China.

Created on Dec 31st 1969 18:00. Viewed 0 times.

Comments

No comment, be the first to comment.
Please sign in before you comment.