Articles

New arrival OBD2 Odometer Correction Tool for Benz 2015-2017

by Xing T. ***

New OBD2 Odometer Correction Tool for Benz 2015-2017 

 

Benz Mileage Correction tools:

Open Mercedes Odometer Correction Software;

First you must ensure that the vehicle battery is sufficiently charged. The process takes 30 to 60 minutes, so the vehicle must be fully charged!
The information display interface contains instructions for the entire procedure.


Supports Following Benz Odometer Reset:

W222 2015-2017
W205 2015-2017
C217 2015-2017
C190 2015-2017
C253 2015-2017
X253 2015-2017
W447 2015-2017
W213 2015-2017 (under development)
-2015 Requires a CAN Filter

 

Instructions: 
 First use the
<1 OBD Read Config Info> option to get the vehicle configuration information;
Then remove the meter, follow the picture to wire, and program the MCU with the
<2 MCU Data Programming> option;
Then reinstall the meter and write the vehicle configuration information with the
<3 OBD Write Config Info> option;
And finally use the
<4 OBD Read Mileage> and
<5 OBD Write Mileage> options to read and write the kilometers.
Modifying the kilometers again is only required to operate in <4 OBD Read Mileage> or <5 OBD Write Mileage> steps!!!

 

20010715784624117343

Note: 
<1 OBD Read Config Info> and <2 OBD Write Config Info> communication takes 15-30 minutes, Please make sure the vehicle battery is sufficient!
Before operating <2 MCU Data Programming>, Please confirm whether the meter is 8-drive or 11-drive.

Step 1: OBD reads configuration information;

If Odometer Correction is supported, here are the tips: Make sure the vehicle battery is sufficient.
If Odometer Correction is not supported, here are the tips: For cars before 15 years, you need to add a filter, and then you can operate steps 4(OBD read kilometers) and steps 5(OBD write kilometers); cars after 17 years do not support Odometer Correction temporarily. 

Take the calibration process of Benz 205 chassis instrument for 16 years as an example:

Step 1: OBD reads configuration information
Configuration data must be saved after successful reading!

Step 2: The MCU edits the data
At this time, you need to remove the back cover of the dashboard, select the type, and select the wiring method according to the type.
You can open the wiring diagram directly,there are 5 wires in total(as the picture). The Dashboard is divided into 8 drives and 11 drives.


benz-obd-mileage-programmer
After connecting the wires according to the wiring diagram, perform the operation.
If the MCU data is edited successfully, the wiring can be removed. 

Step 3: Write configuration information
The configuration information is the data read in the first step, and you can select the saved data at this time;
Then you can get the prompt that the vehicle configuration information is written successfully
 
Step 4: You can adjust the mileage
Read the kilometers first, and then write the kilometers
For example, we wrote the mileage of 12345;Then read it out is 12345km.
 
Look at the dashboard again, the kilometers are correct! The steps are complete!


Package includes:

1set x OBD2 Odometer Correction Tool 


https://www.aliexpress.com/item/4000603297931.html


Sponsor Ads


About Xing T. Advanced    ***

67 connections, 0 recommendations, 434 honor points.
Joined APSense since, March 22nd, 2018, From shenzhen, China.

Created on Jan 10th 2020 06:42. Viewed 294 times.

Comments

No comment, be the first to comment.
Please sign in before you comment.