iLink450 OBD2 Scanner EPB Oil Light ABS Airbag SRS TBA/TPS SAS BRT Scan Tool

by Xing T. ***
iLink450 OBD2 Scanner EPB Service Oil light ABS Airbag SRS TBA/TPS SAS reset BRT DPF Regeneration Diagnostic Tool
iLink450 Full Service Tool is specially designed for professional technicians and body shops to service individual specialized systems. The functions include EPB, Oil Service, ABS&SRS reset, Battery Configuration, Steering Angle Sensor Calibration, DPF regeneration and Throttle body alignment.
Support Language:
English, French, German, Polish, Russian, Spanish and much more. 
Default language is English, for other languages, please update via official website.


1. Service/Oil Light Reset coverage for over 40 Asian and European vehicle makes
• Resets Oil Service Light
• Resets Oil Inspection Light
• Sets Inspection Service Interval (1 & 2)
• Sets Inspection Mileage
• Provides on-screen service reset instructions for vehicles which do not support electronic service resets

2. Electronic Parking Brake(EPB) servicing coverage for over 30 Asian and European vehicle makes
• Deactivates and re-activates brake control system
• Retracts calipers for brake pad replacement
• Advances calipers after servicing to the original position, without affecting current calibration
• Reads and clears trouble codes (fault codes)
• Turns off brake warning light
• Initializes the wear indicator if required when new pads installed
• Diagnoses EPB/SBC caliper functionality
• Resets the brake pad thickness after service on Audi A8
• Performs ECU controlled brake fluid change

3.Battery Configuration(BRT)
  After changing battery on cars, particularly if equipped with Start & Stop function and/or regenerative breaking system, a smart battery replacement tool as iLink450 is required to associate the new battery with the vehicle ECU to complete the job and start the engine. iLink450 offers a cost-effective solution for independent garages to work on modern vehicle battery and helps them to get prepared for the future of the battery business. Supports most brands of battery.

4.ABS & Airbag Reset
  Reads and clear codes and turns off ABS/Airbag warning indicator. Performs bi-directional control tests, such as ABS motor test, actuator test, ABS bleeding, airbag reset and so on.

5.Throttle Body Alignment (TBA/TPS)
  After cleaning or replacing the Electronic Throttle Body, adaptation must be carried out (also the case if the negative terminal of the battery has been disconnected or when the Engine Control Unit has been replaced). The iLink450 will perform Electronic Throttle Body adaptations on supported vehicles: For Acura,For Audi,For BYD,For BMW,For Brilliance,For Chery,For Citroen,For Daewoo,For Ford,For Geely,For GM,For Great-Wall,For Honda,For Hyundai,For Infiniti,For JAC,For Kia,For Land Rover,For Lexus,For Lincoln,For Mitsubishi,For Nissan,For Opel,For Peugeot,for Porsche,For Saab,For Seat,For Skoda,For Toyota,For VW.

6.SAS Reset Function
  The Steering Angle Sensor (SAS) is used to measure the angle of the steering wheel and the speed at which it is being turned. The signal is mainly used by the ABS System as part of its stability control function but also by other systems such as ride level control and adaptive lighting. A problem with the SAS Signal will cause a fault with any of the systems that use the signal directly, or indirectly.
  If the Steering Angle Sensor (SAS) needs to be changed, many vehicles require the new sensor to be calibrated. The ilink450 Tool will allow you to carry out steering angle re-calibration on supported models.

7.DPF Regeneration or Replacement
  Carry out a forced Diesel Particulate Filter (DPF) Regeneration is required when the DPF filter blockage reaches levels where passive or active regeneration is unable to burn off the excess soot. The iLink450 is also capable of regenerating Diesel Particulate Filters and resets the DPF light after the filter has been replaced.

• Display: 2.8” Backlit, 320X240 TFT color screen
• Operating Temperature: 0 to 60°C (32 to 140°F)
• Storage Temperature: -20 to 70°C (-4 to 158°F)
• Power: 8 to 18 V provided via vehicle
• Supported Protocols: J1859-41.6, J1850-10.4, ISO9141, KWP2000 (ISO 14230), and CAN (Control Area Network ISO 11898)
• Tool Dimensions: 194*117*47mm (L*W*H)
• Color Box: 220*165*85mm (L*W*H)
• Weight: 0.9KG

Package List:
1 x iLink450 Unit
1 x User’s Guide
1 x TF Memory Card
1 x USB Cable
1 x Leather Carrying Pouch
1 x CD

Sponsor Ads

About Xing T. Advanced    ***

65 connections, 0 recommendations, 408 honor points.
Joined APSense since, March 22nd, 2018, From shenzhen, China.

Created on Jul 29th 2019 07:17. Viewed 323 times.


No comment, be the first to comment.
Please sign in before you comment.