CCEC Cummins Operating Instructions
by Starlight Generator dieselgeneratortech3. Operating
Instructions of CCEC Cummins
3.1
Appearance and Installation Dimension:
3.2 Connection mode
3.2.1
Battery:
1#
Terminal: Power+;2# Terminal: GND
Use
1mm2 or larger copper wire.
3.2.2 Actuator:
3#
& 4# Terminals: Actuator
Use
1mm2 or larger copper wire.
Do
not short circuit the terminals to GND.
3.2.3 Speed Signal:
5#
Terminals: Speed Signal;6# Terminals:
GND for Speed Signal
Make
sure the Common Ground Terminals are unified, when the speed signal source is
common used by more than one equipment.
3.2.4 Remote Speed
Adjust:
A
potentiometer installed on the panel would be connected to 7#, 8# and 9#
terminals as a Remote Speed Adjuster.
The
47K- Ohm Potentiometer’s PN is 3035105. 2# pin should be connect to the 8#
terminal of Control Governor. A 200K-Ohm resistor could be series connection in
the wire in order to improve engine stability, if necessary.
Keep
the 8# and 9# terminals open if Remote Adjusting is not needed.
3.2.5 Idel/Run Mode
Switch:
10
# terminal is Idle / Run mode switch interface. A switch or relay could be
connected between 7# and 10 # terminals.
When
the switch or relay is open, control governor will work in RUN Mode. When the
switch or relay is connected, control governor will work in IDLE Mode.
3.2.6 Common GND
11
# terminal is spare GND, and do not need to be connected. Do not attach the
battery negative to 11 # terminal, the control governor may be damaged.
A#
and B# terminals are damping, it was needed when the oscillation of the
coupling between engine and generator occurred, and do not need to be connected
in general condition.
3.3 Debugging and Use:
3.3.1
Droop
This
Potentiometer is used to set the speed decline percent when the engine is
loaded.
Droop
Potentiometer is used with Gain Potentiometer in order to keep the engine work
stability.
3.3.2 GAIN
This
Potentiometer is used to set the sensitivity of speed adjustment when the
engine’s load is changed.
Gain
Potentiometer is used with Droop Potentiometer in order to keep the engine work
stability.
3.3.3 RUN
This
Potentiometer is used to set the target Run-Speed.
3.3.4 IDLE
This
Potentiometer is used to set the target Idle-Speed.
3.3.5 SMOOTHLY RISING
CONTROL
This
setting time is used to set the sensitivity of Smoke Control.
The
larger potentiometer set, the more smoke control. But too large setting time may
cause difficult engine start.
The
potentiometer is usually arranged on the 10s point.
CCEC Cummins Technical
Advantage
Keeping
pace with the updated technology of Cummins all along, specialized in the
production of the heavy duty and HHP engines varying from 11L-50L and the
extensive power range of engines covers from 224kW to 1657kW.
Advanced
manufacturing technology creates the first-class reliability, durability and
fuel-economy of engines. No matter in what kinds of extreme environment
including in Antarctic, Middle East or Africa and in Qinghai Tibet Plateau,
CCEC engines could provide consistent and robust power for customers.
Make
continuous efforts on new products development to meet the market demands. Its
fully-controlled engines QSNT, QSK19, QSK38, QSK50 meet the Tier3 emission
regulation respectively.
Professional
application engineering teams provide customers with the mature products
application design, on-site technology support and customers training etc.
presales service and help the customers to solve the problems and difficulties
resulted from products application design.
CCEC Quality Advantage
CCEC obtained the Certification from authoritative Bureau Veritas, France and also obtained the ISO9001
ISO/TS16949,ISO14001 and OHSAS18001 certification.
CCEC
execute China National Standards and Cummins Products Technology & Quality
Standards strictly.
CCEC’s
suppliers have been put into Cummins quality control system and the supplying
processes are performed based on Cummins technology and quality standards.
CCEC Service Advantage
Carry
out the same quality assurance and warranty commitment standards as Cummins.
Set
up quick service system according to Cummins Global Standards.
Established
24hrs customer hotline and national service network. About 118 authorized
service dealers and more than 700 professional technicians to provide specialized
service to customers.
The
HHP Engine Technical Training Center in Cummins East Asia is with complete
function.
Provide
free New Engine Inspection service.
Sponsor Ads
Created on May 25th 2019 01:57. Viewed 293 times.