How to Activate 2012 Release 3 Delphi DS150E Softwareby Magic Lee obd2repair
2012 Release 3 Delphi DS150E software for Autocom CDP+ is obd2repair latest Delphi software. 2013 Delphi car diagnostic software is release 3 2012 - Delphi Europe Service Operations. Here OBD2Repair would like to share with you the method to Activate 2012 Release 3 Delphi DS150E Software.
Release 3 2012 Delphi Software
Delphi Car Diagnsotic software
2013 Release 3 2012 delphi autocom
Delphi Euro 5 Diagnostics, Connecting you to the Vehicle Manufacturer
Delphi Euro 5 Diagnostics s you to download software updates to all of the reprogrammable electronic control units of Euro 5 type approved vehicles. The Euro 5 VCI is connected between the vehicle and a PC with Internet connection, it is then possible to purchase and download software directly from the manufacturer’s website.
At now, 2013 Delphi car diagnostic software is release 3 2012 - Delphi Europe Service Operations
The Delphi DS105E offers simple and user-friendly navigation that makes operation fast and efficient, and can be used on Autocom CDP+ from ADKTECH(Professional Car Diagnostic Factory)
1st: Free Download the Delphi Diagnostic PC Software,
DS150E (For cars) / DS350E / DS500E / DS800E
Delphi Diagnostic Application tables
Application List (EU countries)
Application List (Non EU countries)
2st: Open the Delphi Diagnostic software, and install it
choose DS150E, button next
3st: The preparation for activation Release 3 2012 Delphi software
how to block internet access when activating Release 3 2012 Delphi software
Firstly: disconnect your internet, or you can't activate 2012 Release 3 Delphi by USB Stick, by the way, some customer will question, if not disconect from internet, when i activate the 2013 Delphi Release 3 software, how to fix? pls following this way:
open the host (use the notepad). and copy these words to your host file:
If it is cockamamie for your, pls back-up your host file,and then replace your host file by this host file (Download), after the Delphi software have be activated, pls recove your host file,
secondly: remove Autocom Delphi software certificate from your PC
Download the Patch file and remove certificate.rar
following: run : remove certificate.exe
-> it will remove original autocom Delphi certificate from windows certificates folder.
you also can try: run: certmgr.msc in CMD, and choose:
Certificates-current User(need administrator)--Personal-Certificates-Choose Autocom***, and delete it.
Then copy patch content to Delphi installation dir (Must overwriting original files), usually installation dir is C:Program FilesDelphi, if you haven't change the installation dir. for example, the delphi software is installed on D: disk:
Thirdly: Notice: the below two steps have be finished.
After you finished with them, you can start Delphi activation. just try!
1. Open Delphi DS150E software, it will start activation process.
2. Delphi Software activation: input: Serial number:100251,Hardware key:
3. Choose activate via USB stick
4. Insert USB stick to your PC(Min. 1MB Free Space)
5. About 2-5 seconds, The programmer will write information to your USB Stick
6. Eject USB Stick, send the FileActivation.xml on USB stick to us: info at OBD2REPAIR.COM
7: overwriting the old FileActivation.xml by new FileActivation.xml file(from us)
8: Insert USB stick into your PC agian, Now the software is activated.
Notice: pls don't following the step on the Picture, or can't be activated
Release 3 2012 Delphi software:
if you need use the Autocom CDP+ from ADKTECH, you need make frimware update, we can't make sure others supplier autocom CDP+ support frimware update
connect interface to car .( for power )
setting , hw test , it wll have a message ask about frimware update .
clict to ok and it wll make frimware update.
you need wait few minute for frimware update
.( when is make frimware update ,dont close software or dont remove power ,etc )
then you can use Delphi 2012 release3
Created on Dec 31st 1969 18:00. Viewed 0 times.